You experience a port assignment conflict. The default port assigned to RDP is After a Remote Desktop server client loses the connection to a Remote Desktop server, you experience one of the following symptoms:. If the client logs back in to the same Remote Desktop server, a new session may be established, and the original session may remain active.
Because of a security error, the client could not connect to the Terminal server. After making sure that you are logged on to the network, try connecting to the server again. Remote desktop disconnected. Because of a security error, the client could not connect to the remote computer. Verify that you are logged onto the network and then try connecting again. Remote Desktop Services clients are repeatedly denied access to the Remote Desktop server.
If you are using a Remote Desktop Services client to log on to the Remote Desktop server, you may receive one of the following error messages. Open the System item in Control Panel. Under Remote Desktop , select either of the available options, depending on your security requirements:.
Allow connections from computers from computers running any version of Remote Desktop less secure. Allow connections from computers only from computers running Remote Desktop with Network Level Authentication more secure. If you select Don't allow connections to this computer on the Remote tab, no users will be able to connect remotely to this computer, even if they are members of the Remote Desktop Users group.
In the RD Maximum Connections allowed box, type the maximum number of connections that you want to allow, and then click OK. Under Connections , right-click the name of the connection, and then click Properties.
On the Network Adapter tab, click Maximum connections , enter the number of simultaneous remote connections that you want to allow for the connection, and then click OK. If the Maximum connections option is selected and dimmed, the Limit number of connections Group Policy setting has been enabled and has been applied to the RD Session Host server.
You can add users and groups to the Remote Desktop Users group by using the following tools:. Membership in the local Administrators group, or equivalent, on the RD Session Host server that you plan to configure, is the minimum required to complete this procedure. Start the System tool. If you select the Don't allow connections to this computer option on the Remote tab, no users will be able to connect remotely to this computer, even if they are members of the Remote Desktop Users group.
This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, seeHow to back up and restore the registry in Windows.
To resolve this problem, determine which application is using the same port as RDP. If the port assignment for that application cannot be changed, change the port assigned to RDP by changing the registry.
After you change the registry, you must restart the Remote Desktop Services service. After you restart the Remote Desktop Services service, you should verify that the RDP port has been changed correctly.
The listener component runs on the Remote Desktop server and is responsible for listening for and accepting new Remote Desktop Protocol RDP client connections, thereby allowing users to establish new remote sessions on the Remote Desktop server. There is a listener for each Remote Desktop Services connection that exists on the Remote Desktop server. Go to Settings System.
Applies to: Windows 10, Windows Server When you connect to your PC by using a Remote Desktop client, you're creating a peer-to-peer connection. You have a couple of options: use port forwarding or set up a VPN. Specific steps for enabling port forwarding depend on the router you're using, so you'll need to search online for your router's instructions.
Find the network configuration with an 'Operational' status and then get the IPv4 address. Your public IP address the router's IP.
Port number being mapped. To open a port in your Windows firewall, first, hit the Windows key and type "allow". Next, click on "Allow an app through Windows Firewall". The screenshot below shows you what this step looks like in Windows Next, you will need to scroll through the list of apps and find Remote Desktop. Check the box next to Remote Desktop to enable it through your firewall. We have free Router Detector software to help you find your router's IP address.
The software is part of our Network Utilities suite of tools and it is completely free to use. We have Network Utilities software that can forward ports for you. With Network Utilities , you can easily forward ports and also un-forward ports quickly so that you can keep your network up to date with the ports that you need forwarded and maximize your network security.
0コメント