Rm2652 dometic manual

Ne pas entreposer ni utiliser de l'essence ni. Lisez attentivement le mode d'em-. Pour obtenir de. Previous Page. Next Page. Dometic RM User Manual 24 pages. Classic series refrigerator for lp-gas and electric operation 17 pages. Page 4 11 inches water column. Page 5: Securing The Refrigerator This refrigerator model is not designed for 12 volt DC operation of the cooling system; however, a continuous 12 volt DC must be supplied to the refrigerator to oper- ate the controls.

Use a minimum of a 14 gauge wire between the battery and refrigerator to supply the con- trol voltage. Page 6: Drain Water Hose 2. Once the lower front strip is slipped under the hinge, the part is possible to swing into place as shown in FIG.

Secure the refrigerator and the lower front strip with two screws: One screw through the hinge, and on the opposite side one screw through the lower front strip. Page 8: Operating Instructions If the refrigerator is operated when it is not level and the ve- hicle is not moving, liquid ammonia will accumulate in sections of the evaporator tubing. This will slow the cir- culation of hydrogen and ammonia gas, or in severe cases, completely block it, resulting in a loss of cooling.

Page 9: Auto Mode AC is not available , it may take longer than 45 sec- onds to allow air to be purged from the gas line. If the refrigerator has not been used for a long time or the LP tanks have just been refilled, air may be trapped in the supply lines. The control system will attempt a new ignition sequence. Page How To Use The Refrigerator For faster ice making, the trays should be placed in direct contact with the bottom of the freezer compartment.

Refrigerator volume. Total refrigerated volume is 6 cu. Total refrigerated volume is 8 cu. It is important to keep the area at the back of the refrigerator clean.

Page Troubleshooting B. Check all connections in the LP gas system at the back of the refrigerator for gas leaks. The LP gas supply must be turned on. Apply a non-corrosive bubble solution to all LP gas connections. The appearance of bubbles indicates a leak and Part No. If a longer hose is required, follow the illustration shown below:. NOTE: Black water check valve must be reinstalled to ensure proper refrigerator operation.

In vehicles where routing the drain hose through the floor is not possible, a metal clip is available. The clip is used to drain water out through the side vent. Part No. When installing the refrigerator in the enclosure, all areas within the recess in which the refrigerator is installed must be sealed.

Make sure that there is a complete seal between the front frame of the refrigerator and the top, sides and bottom of the enclosure. A length of sealing strip is applied to the rear surface of the front frame for this purpose.

Also apply a sealing strip to the foremost floor of the enclosure and apply a second sealing strip to the bottom of the trim strip on the front base as shown in FIG. The sealing should provide complete isolation of the appliance's combustion system from the vehicle interior. A wood strip must be in place across the upper opening of the enclosure. The top frame of the refrigerator will be anchored to the wood strip with screws. See FIG. The dimensions shown in FIG. NOTE : If the door is hinged and it needs be changed to the opposite side, it must be done before the refrigerator is installed in the enclosure.

See Step. NOTE : Be careful not to damage the sealing strip applied to the floor of the enclosure when the refrigerator is put in place. The refrigerator is secured in the enclosure with six screws. They must be installed in the following order:. First: Two screws are installed in front decoration strip and through the front base. The strip is shipped as a loose part. The hinge plate can be on the right or left side depending on the door swing.

The second screw is installed with a washer on the opposite side. Open refrigerator door and gently push the tabs out of the hole in the hinge with flat blade screwdriver. Be careful not to pinch the wires. Make sure the tabs snap back into the holes in the hinge plate. Third: Two screws installed as shown in rear base. Failure to follow the sequence in securing the refrigerator in the enclosure can cause leakage between the frame and cabinet.

All completed connections should be checked for leaks with a noncorrosive leak detector. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions.

Enter a new password. RM In the U. Any applicable local code. In Canada, the installation must conform with: 1. For certified vent system kits, see Section B.